Search results

I want to build a canopy for my 58g. It's the standard 36"x18" Oceanic RR tank. Ive been putting off building the canopy for over a year now, so it's time to get busy. I currently have two 150w hqi pendants hanging over the tank, but I want to have it set up with two metal halides and two T12...

My tank is not yet covered(I will be constructing a screen this weekend to cover it), but i hadn't had any problems with fish jumping until my sixline wrasse went missing 2 weeks ago. I looked all around the tank and even in the overflow briefly but didn't see him anywhere. Yesterday I was...

Well I am sad to report that one of my favorite little corals has suffered from rapid tissue neucrosis it appears. It is my green milli that was starting to grow really fast that seemed fine yesterday, then first thing this morning was nothing more than a bright white skeleton. Here's a...

So I was doing a water change yesterday and had my hands in the water when I noticed a tingling on a small cut on my finger every time I put my hand in the water. After unplugging each peice of equipment one by one I found it was my koralia 3 that's less than one year old. I've read these are...

Anyone know what this is? I think it's supposedto be a Acropora Tenuis, but I'm not sure. alt=""> Thanks.

I started my tank with Coralife salt and I was not aware of how high the calcium was in that mix. According to this site http://aquariumwatertesting.com/AWT_Salt_Analysis_0208.pdf the average calcium is around 450 with salinity at 30 parts per thousand, but my water tests at 660 at 1.026. I have...

So I've been having a lot of micro bubbles caused by the anti syphon hole in the return line being too high and it's above the water line doing it's own Venturi thing. I need to fix this. Anyhow, where the bubbles get trapped on the underside of my monti cap the constant air under there has...

I got a bunch of new rock a few months back that was covered thick with really purple coraline. At the time I had a 250W HQI fixture, Phoenix 14k bulb and 2 T5 actinics for lighting. I changed lights and now I have two 150W coralife pendants and they are burning the coralife 14k bulbs. I have no...

I wish i could get a pic of these, but they are too small for my camera to focus on. They look like a really thin worm, thicker than a hair and fuzzy looking. It is hanging out of my chaeto in the fuge and it kind of jerks every 5 or 10 seconds. I can see two of them and they're pretty long...

I have had 2 little spots where this algae has been growing on a birdsnest coral and I can't seem to get it to stop. I pick it off and have increased the flow on it but it just keeps growing back in the same spot. This is a purple polyp birdsnest and it's lost quite a bit of color the past few...

I have a question about my refractometer. When I look through the eyepiece and I'm supposed to read where the blue and white sections meet, the problem is that there are three lines of blue. Under the big blue section there are two thin blue lines. Do I just read where the big section of blue is...

This is my first time setting up a reef ready system and I have to say I'm pretty excited! I've managed to keep a 35G hex non-rr with sps going good for about a year now, and I'm ready for the step into the wonderful world of sumps and refugiums. I bought this setup used and it is almost 4 years...

I'm having a problem with the drain from the overflow foaming in the sump. The drain line is 1 1/4". I have vinyl tubing going into pvc, then a tee going to refugium, with a valve after the tee on both the drain and fuge line for more control. I had a diy bubble tower with rubble and it wasn't...

Okay this is my first RR tank and I've read a lot about sumps and overflows and such but I seem to have a problem. I bought the tank used and all it had was 1 1/4" nylon tubing draining into a 10G sump, then the flow went over a baffle, then the next area was a refugium zone, then it flowed over...

I recently bought a lightly used 58G glass tank that I'm tying to get going, and it has quite a lot of dried coralline on the back and sides of the glass, as well as the overflow. I have taken all the sand out, and I've been trying to scrape it with a hard plastic scraper and it is pretty tough...

I have a 35G hex tank that is acrylic and it has an annoying top piece of acrylic on it that I'd like to take some off. Here is a pic.photo.jpg I'd like to cut diagonally from the little back slot to the rectangular opening, and then pretty much the same thing around the front. The way it is...

I was observing the tank earlier and saw what looks like a tiny white horseshoe crab crawling on one of my scarlet hermit crabs shell. It is way too small for me to get a pic(I don't have a decent camera), but I would say it's a little smaller than a sesame seed. It scoots around pretty fast...

Ok, I had my 250W MH 14k hanging about 16" over the water level and the sandbed is 21" down from the top of the water. I have been growing sps very well with this scenario. However, I just got a new fixture with a 250W MH that has legs and isn't situated to hang and I would like to set it over...

I just got a cpr bakpak skimmer going on my tank and I was thinking about using the outflow area to drop in some chaeto. I've read quite a lot online about people doing this, but I wanted to get some advise from the club to see the ups and possible downs of doing this. I want to know if anyone...

I've had this tank running for about 5 months now. All parameters have been steady. Here they are from within the last hour; Calcium- 480(this is the average of the API test done 3 x's) Alk- 10.0 dKH Salinity- 1.024 Temp.- 78F pH- 8.0 Mag.- I don't have a test atm. Phosphates- 0. undetectable...